ישנם כיום מספר סוגים של מסכי מגע. הם: התנגדות (שכבה-כפולה), קיבולי משטח ואינדוקטיביים, גל אקוסטי משטח, אינפרא אדום וגל מכופף, דיגיטיזר פעיל והדמיה אופטית. . ניתן לחלק אותם לשני סוגים. סוג אחד דורש ITO, כמו שלושת הסוגים הראשונים של מסכי מגע, וסוג המבנה השני אינו דורש ITO, כמו המסכים האחרונים.
Touch screens are everywhere around us. In the field of personal portable devices such as PDAs, touch screens save space and are easy to carry, as well as better human-computer interaction. Currently on the market, resistive touch screens and capacitive touch screens using ITO materials are the most widely used.
Resistive touch screen
ITO is the English abbreviation for indium tin oxide, which is a transparent electrical conductor. The properties of this substance can be adjusted by adjusting the ratio of indium to tin, the deposition method, the degree of oxidation, and the size of the crystal grains. Thin ITO materials have good transparency, but high impedance; thick ITO materials have low impedance, but transparency will deteriorate. When depositing on PET polyester film, the reaction temperature should drop below 150 degrees, which will lead to incomplete oxidation of ITO. In subsequent applications, ITO will be exposed to air or air barriers, and its unit area impedance will vary due to self-oxidation. Change of time. This makes the resistive touch screen need to be calibrated frequently.
Figure 1 is a side cross-sectional view of the resistive touch screen. The surface touched by the finger is a hard coating to protect the underlying PET layer. The PET layer is a thin, flexible PET film that bends downward when the surface is touched, and allows the two layers of ITO coating below to contact each other and connect the circuit at this point. Between the two ITO layers are some isolation fulcrums about one thousandth of an inch thick to separate the two layers. At the bottom is a transparent hard bottom layer to support the structure above, usually glass or plastic.
The multi-layer structure of the resistive touch screen will cause a lot of light loss. For handheld devices, it is usually necessary to increase the backlight source to make up for the problem of poor light transmission, but this will also increase battery consumption. The advantage of the resistive touch screen is that its screen and control system are relatively cheap, and the response sensitivity is also very good.
capacitive touch screen
Capacitive touch screen also needs to use ITO material, and its low power consumption and long life, but the higher cost makes it less concerned before. The friendly man-machine interface and smooth operation performance provided by Apple's iPhone have made the capacitive touch screen popular in the market, and various capacitive touch screen products have appeared one after another. And as the process progresses and mass production, its cost continues to drop, and it begins to gradually replace the resistive touch screen.
The surface capacitive touch screen only uses a single layer of ITO, when a finger touches the surface of the screen, a certain amount of electric charge will be transferred to the human body. In order to recover these charge losses, the charge is replenished from the four corners of the screen. The amount of charge added in each direction is proportional to the distance of the touch point, and we can calculate the position of the touch point from this.
Surface capacitance ITO coating usually requires linearized metal electrodes on the periphery of the screen to reduce the influence of corner/edge effects on the electric field. Sometimes there is an ITO shielding layer under the ITO coating to block noise. The surface capacitive touch screen needs to be calibrated at least once before it can be used.
Compared with the surface capacitive touch screen, the inductive capacitive touch screen can penetrate a thicker cover layer and does not require correction. The inductive capacitive type etches different ITO modules on the two layers of ITO coatings. It is necessary to consider the total impedance of the modules, the impedance of the connecting lines between the modules, and the parasitic capacitance generated at the intersection of the two layers of ITO modules. And in order to detect the finger touch, the area of the ITO module should be smaller than the area of the finger. When a diamond pattern is used, the diagonal length is usually controlled at 4 to 6 mm.
In Figure 3, the green and blue ITO modules are located on the two layers of ITO coating. They can be regarded as continuously changing sliders in the X and Y directions. Different ITO modules in the X and Y directions need to be scanned separately. Obtain the location of the touch point and the trajectory of the touch. Between the two layers of ITO coating is a PET or glass isolation layer. The latter has better light transmission, can withstand greater pressure, and has a higher yield. It can be directly plated on the LCD surface through a special process, but it is also heavier. The thinner this isolation layer, the better the light transmittance, but the greater the parasitic capacitance between the two layers of ITO.
מיקום המגע שזוהה על ידי מסך המגע הקיבולי תואם לנקודת הצלב שבה מורגש ערך שינוי הקיבול המרבי. עבור ציר X- או Y-, זהו הממוצע המשוקלל של כמות האות של מודולי ITO שונים כדי לקבל את כמות המיקום, ואז המערכת נמצאת מתחת למסך המגע. נקודת המגע או הרצועה מוצגים ב-LCD.
כאשר שתי אצבעות נוגעות (שתי נקודות אדומות), יהיו שני ערכים מקסימליים בכל ציר. בשלב זה, ישנם שני שילובים אפשריים, והמערכת אינה יכולה לאתר ולשפוט במדויק. זה מה שאנו מכנים בדרך כלל נקודות שיקוף (שתי נקודות כחולות).
בנוסף, החלק התחתון של מסך המגע הוא תצוגת ה-LCD, וגם פני השטח שלו מוליכים. זה ייצור קיבול טפילי עם מודול ITO מצופה ITO הסמוך. בדרך כלל עלינו לשמור שכבת אוויר מסוימת בין שתי השכבות. הפחת את ההשפעה של קיבול טפילי.
Capacitive touch screen solution
Among the current capacitive touch screen solutions, Cypress PSoC products are in a leading position with programmable, flexible design, good consistency, and efficient PSoC Express / PSoC designer development environment.
PSoC CapSense technology is implemented using CSA or CSD modules based on the principle of capacitive sensing. There will be parasitic capacitances between adjacent sensing modules or wires on the PCB or touch screen (see Cp in Figure 4). When a finger approaches or touches two adjacent sensing modules, it is equivalent to adding two capacitances. It is equivalent to the capacitor Cf connected in parallel to Cp. Using PSoC's CSA and CSD technology can detect the change on this capacitance, so as to determine whether there is a finger touch.
The advantages of the PSoC touch screen solution are also reflected in:
1. It is a single-chip solution, which reduces the external components compared with the traditional solution and reduces the overall BOM cost of the system.
2. By using I2C-USB Bridge and other related tools, combined with the PSoC Express / PSoC designer development environment, you can greatly save development time and costs.
3. PSoC's internal IO and various analog/digital modules can be dynamically reconfigured, and the design can be updated to meet new requirements without modifying the schematic and PCB. It also supports a variety of communication interfaces I2C / UART / SPI / USB, etc., and can be easily connected to hosts with various interfaces, which will reduce the cost of system updates.
4. PSoC can flexibly set parameters in response to changes in the external environment-RF interference / temperature changes / power fluctuations, etc., and has been widely used in touch control of LCD displays, mobile phones, digital cameras and white goods.
5. In addition to controlling touch, PSoC can also realize value-added functions such as LED backlight control, motor control, power management, and I/O expansion.
PSoC has been applied to touch screens of various sizes. If you want to realize the control of surface capacitive touch screens, you can use the CY8C21x34 or CY8C24x94 series to realize it through the CSD module, as shown in Figure 5. The control of the inductive capacitive touch screen can be realized by the CY8C20x34 series through the CSA module, or by the CY8C21x34 or CY8C24x94 series through the CSD module.
In the design of touch screen products, performance and cost need to be weighed. The cost of resistive touch screens is low, competition is fierce, and there are certain limitations in performance and applications.
1. The capacitive touch screen only needs touch, not pressure to generate signals.
2. The capacitive touch screen only needs one time or no calibration at all after production, while the resistance technology requires regular calibration.
3. The life of the capacitive solution will be longer, because the parts in the capacitive touch screen do not require any movement. In resistive touch screens, the upper ITO film needs to be thin enough to be flexible so as to bend downward to contact the lower ITO film.
4. Capacitance technology is superior to resistance technology in terms of light loss and system power consumption.
5. The choice between capacitive technology or resistive technology mainly depends on the object that touches the screen. If it is touched by a finger, a capacitive touch screen is a better choice. If you need a stylus, whether it is plastic or metal, a resistive touch screen can do the job. The capacitive touch screen can also use a stylus, but it needs a special stylus to cooperate.
6. The surface capacitive type can be used for large-size touch screens, and the relative cost is also low, but currently it cannot support gesture recognition; the inductive capacitive type is mainly used for small and medium-sized touch screens, and can support gesture recognition.
7. Capacitive technology is wear-resistant, has a long life, and has low maintenance costs when users use it. Therefore, the overall operating cost of the manufacturer can be further reduced.
The development trend of capacitive touch screen
Capacitive touch screens have been applied to iPhones and other handheld devices. Positioning a single-point track/simulating a double-click on a mouse is its basic function, and the recognition and application of multi-finger gesture operations has become a hot spot in the current market. In portable applications, the user holds the device in one hand and can only operate with the other hand. Therefore, it is particularly important to recognize gesture operations such as multi-finger grasping/translation, stretching/compression, rotation, and page turning. The PSoC inductive capacitive touch screen can already achieve multi-point detection to support two-finger gesture recognition. It is foreseeable that capacitive touch screens that support gesture recognition will shine in the market.

